鼎尚时时彩平台二维码首页

Inquiry Cart  鼎尚时时彩平台ios首页

No products

Send Inquiry

鼎尚时时彩平台在线官网

http://www.
  Tel: +86-18662902598
 Fax: +86-513-82795188
Mail:commerce@

鼎尚时时彩平台在线官网

 

鼎尚时时彩平台官方ios
鼎尚时时彩平台线路网址
鼎尚时时彩平台地址网站
In addition to the physical appearance of the surface of the commutator, the skin or patina is of equal importance for the good running of the carbon brushes. Each carbon brush builds a characteristic patina which is affected by operating and ambient conditions. The patina consists mainly of copper oxides, graphite deposits and adsorbed water, and its appearance is of importance when assessing the most suitable brush grade. The following pictures show typical appearances of commutation surfaces.
The pictures are not of an international standard specification but are used by carbon brush manufacturers and users of brushers as a guide to assist in judging the operation of carbon brushes.
鼎尚时时彩平台平台注册

 

  

P2, P4 and P6 are examples of normal skin or patina formation. When a machine runs well, the patina or skin on a commutator will be even, slightly shiny and coppery brown to black in colour. There may be appearance of greyish, blueish and reddish hues. but of importance is the evenness of the skin formation and not its colour.

 

鼎尚时时彩平台平台注册

 


 

P12 • Appearance: Streaky patina having some wide and narrow tracks of different colour.
No commutator wear.
Causes: High humidity, oil vapour, aggressive gases in the atmosphere, low electrical load on the brushes.

 

P14 • Appearance: Torn patina, general appearance as in P12, but with narrower tracks and commutator wear.
Causes: As in P12, but the condi-tions have been maintained for a longer period causing commu-tator damage.

 

P16 • Appearance: Smutty patina, uneven skin having patchy colours and random spots.
Causes: Uneven commutator or unclean operating conditions.

 

P22 • Appearance: Patina with dark areas, regular or irregular patches covering one or more commutator segments.
Causes: Out of round commutator, vibrations of the motor caused by badly adjusted shaft or damaged bearings.

 

P24 • Appearance: Dark patchy patina having definite edges as in Tl2 and T14.
Causes: Raised segment or group of segments causing the brush to bounce.

 

P26 • Appearance: Commutator segments having patches in the middle or at the edges.
Causes: Often due to faulty grinding of the commutator.

 

P42 • Appearance: Alternating light and dark bar markings .
Causes: Uneven current distribution over two parallel windings caused by double windings crossing in the same slot.

 

P46 • Appearance: Mat patches in double pole pitches .
Causes: Usually by faulty soldering of the risers or segment connections.

 

鼎尚时时彩平台地址网址

 


 

 

 

B2, B6, B8. Appearance: Bar edge burning or burning in the middle of bar.
Causes: Sparking caused by commutation problems.

 

B10 • Appearance: Perforated patina, light, dense or distributed build-up spots.
Causes: Patina destruction caused by too large electrical resistance.

 

鼎尚时时彩平台网站官方

 


 

T10 • Appearance: Dark patches at edge of bars in direction of rotation.
Causes: Frequently caused by long periods with the motor being stationary without power or short stationary periods under load.

 

T12 • Appearance: Burning of a trailing edge and the next leading edge of a bar.
Causes: Caused by protruding segment as in L2.

 

T14 • Appearance: Dark markings.
Causes: Sign of a low segment, could also be caused by a flat spot on the commutator (see L4).

 

T16 • Appearance: Clearly defined dark markings together with segment edges burnt.
Causes: Raised mica (see L6).

 

T18 • Appearance: Dark markings.
Causes: Badly undercut segment edges (see L8).

 

 

 

 

L2 • Protruding segment
L4 • Low segment
L6 • Raised mica
L8 • Ridge on the segment edge
Causes: Faulty commutator segments
L10 • Copper drag
Causes: Bumps or vibrations from various causes

 

鼎尚时时彩平台二维码首页
The following pictures show typical brush-sliding faces. For easy identification we suggest you use the symbols S1, S3 etc.
S1, S3 and S5 are satisfactory sliding faces, indicating that there are no mechanical or electrical problems. Depending on the carbon material the sliding surface appears dense or porous, and shiny dull or matt.
If there is dust in the circulating air fine hairlining may occur as shown in S5.

 


 

S1 • Dense, shining sliding face

Problem free operation

 

S3 • Slight porous sliding face

Problem free operation

 

S5 • Fine hairlining

Normal operation, slight dust influence

 

S7 • Hairlining

Causes: Underloaded, influence of dust, oil or grease.

 

S9 • Tracking with hairlining and groves

Causes: Like S7, but stronger.

 

S11 • Ghostmarks, difficult commutation

Causes: Commutation problems,e.g. false or incorrect position of the neutral zone or interpole.

 

S13 • Burning edge of the leaving or trailing
   edge

Causes: Difficult commutation, heavy sparking, interruption of contact due to out of round of commutator or insufficient brush holder spring pressure.

 

S15 • Eroded brush face

Causes: Electrical overload, interruption of contact.

 

S17 • Lamination of sliding face

Causes: Burned segments of the sliding face caused by a winding fault giving voltage surge during commutation.

 

S19 • Double facing here for a twin brush

Causes: Tilting of the brush in dual direction machine.

 

S21 • Copper nests

Causes: Pick up of copper particles, often following copper drag.

 

S23 • Broken edges

Causes: High raised lamination, commutator seriously out of round, brush chatter.